logo
USD
ContentGPUsASICsCPUsFPGAsCalculatorGPU CalculatorCPU CalculatorCoinsMinerOptionsMinersPools
 
 
 
lolMiner
Info for both supported coins, parameters, and changelog for lolMiner.
Contact
--cclk
[Miner parameter]
You can set locked/absolute core for NVIDIA Ampere cards through the paramter --cclk.

--cclk 1200,1300

Will make GPU0 lock core to 1200, while GPU1 will lock core to 1300.
--devices
[Miner parameter]
The devices (GPUs) the miner will use. You can use ALL, AMD, NVIDIA or a a comma separated list.

Examples:
--devices AMD
--devices 0,3,4(Will use GPU0, GPU3 and GPU4)
--dualfactor
[Miner parameter]
Lets you control how much hashrate for the second coin/algo the miner aims for.

--dualfactor 5,auto,0 will make GPU0 aim for 5x the hashrate of the first algo, GPU1 auto-tune, while GPU2 will disable second algo, and only mine the first algo!
--lhrtune
[Miner parameter]
To set a pre-defined target of LHR semiunlock. You can set it to 0 or off to disable.

--lhrtune 76.3,0,77.2

This will make the tuning of GPU0 to aim for 76.3% unlock, disable lhrtune for GPU1 and the GPU2 will aim for 77.2%.

Please notice that the initial tuning still needs to be done, but with specified lhrtune, the semi-unlocker may reach the set value quicker (if possible).
--lhrwait
[Miner parameter]
With --lhrwait you can specify a delay before the tuning of LHR starts. Usefull if you are using delayed OC, as the tuning should be done, when the OC have been applied.

--lhrwait 60

Will wait with LHR tuning for 60 seconds.
--maxdualimpact
[Miner parameter]
Adjust how much ETH-speed you can afford to lose, to gain speed on the second algo - normally TON or ALPH. The miner uses a build in tuning progress to optimize the ratio between ETH and the second algo.

Default values are:
Default values used to be:

Ampere0.5
Turing4
Pascal4
RDNA 20.75
RDNA2
Vega3
Polaris3

If your rig have 6 gpus, and you want to adjust GPU3 and GPU4 (Fourth and fifth GPU), and disabling second algo (ETH only) on GPU1 (second GPU), you simple add --maxdualimpact *,0,*,4,6,* to your miner options. This will let GPU0, GPU2 and GPU5 run default values, indicated by the *, while GPU3 uses 4% and GPU4 uses 6% possible ETH speed loss. GPU1 will only mine ETH.

Examples with command added:

-a ETHASH -p eu1.ethermine.org:4444 -u 0x222222.WORKER --dualmode TONDUAL --dualuser EQ222222 --dualpool https://next.ton-pool.com --apiport 4444 --tls 0 --watchdogscript reboot.sh --maxdualimpact *,0,*,4,6,*
--mclk
[Miner parameter]
Locks the memory clock. On core heavy algorithms, this will save power usage!
--silence
[Miner parameter]
Controls the amount of information the miner will print in the console, while its work

--silence 0
Default behavior - will show all info.

--silence 1
Turns off "New job"-messages

--silence 2
Turns off "New job"-messages
Turn off "Found shares"-messages, but the * in 15s stats will tell you found/how many shares.

--silence 3
Will only show the "Longstats" (1 minute stats by default)
 
 
Disclaimer! Hashrate.no utilizes some affiliate and referral links which may generate a small commission. Thanks for supporting us! We also use cookies to track users' input, like, but not limited to power cost, sorting, filters, and prices. We make no warranties of any kind in relation to our content, including but not limited to accuracy and updatedness. Hashrate.no are NOT responsible for any damage; always set your overclock at YOUR own risk and please gain knowledge and do your research! We are not responsible for external links and information that is found there. © Lineo AS 2021-2024